Glossary

The maximum stress a designer can assume that the parts will stand. Is always less than the minimum strength of the material. For example, the ASME Boiler and Pressure Vessel Code typically specifies an allowable stress that is one-quarter of the service temperature yield strength of the material. This introduces a four-to-one safety factor into the design process and is intended to compensate for uncertainties in estimates of strength, service loads, etc.

A design procedure developed for the AISC by the Research Council on Structural Connections. Purposely underestimates the strengths of bolts and joint materials to introduce safety factors into the design of structural steel joints. Is an alternative to the more recently defined load and resistance factor design procedure.

That electrode in a battery or corrosi on cell which produces electrons. It is the electrode which is destroyed (corrodes).

The American Society of Mechanical Engineers.
 

Gasket material manufactured by a paper-making process.

Washer with a slightly conical shape, which acts as a spring
when compressed axially.

A substance (usually organic) used to bond the components of a
gasket material into a matrix.

A large and complex document maintained and published by the American Society of Mechanical Engineers (ASME). The
code describes design rules, material properties, inspection techniques, fabrication vessels. The recommendations of the
Code have been adopted by most states, and have influenced similar Codes in many countries.techniques, etc., for boilers
and pressure

Officially, a threaded fastener designed to be used with a nut. The word is often used interchangeably with Threaded fastener
for convenience.

A bolt is said to be brittle if it will break when stretched only a small amount past its yield point.

That electrode in a battery or corrosion cell which attracts electrons.

An extension of a gasket for the purpose of locating it centrally on a flange.

The equal and opposite forces which exist at the interface between two joint members. The clamping force is created by
tightening the bolts, but is not always equal to the combined tension in the bolts. Hole interference problems, for example,
can create a difference between clamping force and bolt loads.

Gasket material, primarily containing fibers, rubber and fillers, manufactured on a calendar under high load.

Percentage reduction of thickness under a compressive pressure, applied at a constant rate, at room temperature.

Residual deformation of a gasket after it has been subjected to, and then released from a specified compressive pressure, over a defined time and at a given temperature.

Property of gasket material to swell to a defined extent when in contact with the retained fluid, to provide additional sealing
pressure.

A natural “battery” formed when two metals having different electrical potentials (an Anode and a Cathode) are connected together in the presence of a liquid (the Electrolyte).

Metal gasket usually incorporating a filler material in the well of the corrugations, in which the seal is formed between the peaks of the corrugations and the mating flanges.

The slow, plastic deformation of a body under heavy loads. Time-dependent plasticity.

Percentage loss of thickness over a specified time under constant load, applied at a specified rate, at a specified temperature.

Cross-linking reaction of elastomer with various chemicals, creating a matrix of greater stability.

A gasket design in which the gasket material is enclosed within an outer metal cover.

If a bolt can be stretched well past its yield point before breaking it is said to be ductile. (See also brittle)

The external load on a fastener or groups of fasteners is said to be eccentric if the resultant of that load does not pass through the centroid of the group of fasteners (eccentric shear load) or does not coincide with the bolt axis (eccentric tensile load).

The grip length plus some portion of the bolt (often one-half of the thickness of the nuts) which lies within the nut(s) plus some portion (often one-half the thickness) of the head.  Used in stiffness and stretch calculations.

Distance between the geometric center of the part and the circle of points through which the resultant contact forces between mating parts passes.  Must be determined by integration.

That part of the actual width of a gasket considered to contribute to the performance of the gasket.

When a bolt is tightened it partially compresses the joint members “in its own neighborhood.”  When nearby bolts are tightened later, they further compress the joint in this region. This allows the first bolt to relax a little (lose a little preload). Tightening bolts on the opposite side of the joint, however, might INCREASE preload in some of the earlier bolts tightened on the near side.  These shifts and changes in the elastic energy stored in individual bolts, during assembly, are called elastic interactions.

Property of a body to recover its original size and shape immediately after removal of the external forces which cause it to deform.

Generally long chain polymer molecules, which show elastic properties.

The two metallic bodies in a battery or Corrosion cell which give up electrons (the Anode) or which attract them (the Cathode).

The liquid with which the Electrodes of a battery or Corrosion cell are wetted.

Localized plastic deformation in heavily loaded fasteners allows one part to sink into, or smooth the surface of, a softer or more heavily loaded second part.  Nuts embed themselves in joint surfaces.  Bolt threads embed themselves in nut threads, etc.

That completely reversing stress limit below which a bolt or joint member will have an essentially infinite life under cyclic fatigue loads.  Note that the mean stress on the bolts here is zero.

A gasket design in which the gasket material is enclosed within an outer cover (typically PTFE) to minimize chemical degradation by the sealed fluid.

Any instrument which measures the change in length of a part as the part is loaded.

Forces exerted on fastener and/or joint members by such external factors as weight, wind, inertia, vibration, temperature expansion, pressure, etc.  Does not equal the Working load in the fastener.

Metallic cover around inner periphery of gasket material, to minimize chemical degradation by the sealed fluid.  Depending on selection of geometry and metal, it may also improve sealability and blowout resistance.

Term implying that the bolt has broken or the threads have stripped.  There can be many reasons for this.

Failure of a bolted joint to behave as intended by the designer. Failure can be caused or accompanied by broken or lost bolts, but can also mean joint slip or leakage from a gasketed joint even if all bolts still remain whole and in place.  Common reasons for joint failure include vibration loosening, poor assembly practices, improper design, unexpected service loads or conditions, etc.

Basic component of a gasketed joint assembly, incorporating a substantially radially extending collar for the purpose of joining two or more items of process equipment.

Deformation of a flange caused by imposed forces.

A flange where the entire mating faces are flat.

Measure of the ability of the material to resist chemical attack.

A chemical or mixture of chemicals, in any physical form, which represents an unanticipated leak, from anywhere on an industrial site.

A gasket which covers the entire flange surface extending beyond the bolt holes.

An extreme form of adhesive wear, in which large chunks of one part stick to the mating part (during sliding contact).

The coating on a fastener is said to provide galvanic protection if it is more anodic than the fastener and will, therefore, be destroyed instead of the fastener.  Zinc plate (galvanizing) provides galvanic protection to steel fasteners, for example.

Deformable material (or combination of materials) intended to be clamped between flanges to prevent leakage of contained fluid.

Experimentally derived “constants” used to define the behavior of a gasket and/or the assembly and in-service conditions required for acceptable behavior.  The term “gasket factor” comes from the Boiler and Pressure Vessel Code, which contains tabulation of m and y factors defining the recommended Gasket stress in-service and at assembly-for design purposes only.  (Actual assembly and in-service stresses will usually be greater.)  New factors, called Gb, a, and Gs, have recently been proposed for the Code.  These factors are not design recommendations, but instead, define the behavior of the gasket.

The assembly of components (e.g. flanges, bolts, gaskets) required to join two or more items of process equipment and to prevent leakage.

Point at which the load on a gasket can be considered to react for moment calculation purposes.

Effective compressive load per unit of gasket area.

The contact stress exerted on the gasket by the joint members.

Combined thickness of all the things clamped together by the bolt and nut, including washers, gaskets, and joint members.

Differentiation between predominantly hard, metal-based gasket (e.g. spiral wound) and softer or fibre-reinforced materials.

Percentage reduction in thickness under constant compressive pressure at elevated temperature.

Relieving force caused by the pressure of the retained fluid, resulting in a reduction in gasket pressure and an increase in bolt load.

An air-or electric-powered wrench in which multiple blows from tiny hammers are used to produce output torque to tighten fasteners.

The tension created in a single bolt as it is tightened.  Will usually be modified by subsequent assembly operations (see Elastic interactions) and/or by in-service loads and conditions.

A gasket lying wholly within a ring of bolts.

Fluid pressure applied to the joint.

Metal gasket with grooved faces, with or without resilient sealing layer on surfaces.

Quantity of fluid passing through the body and/or over the faces of a gasket per unit periphery of the gasket over a specified time.

Application of a spring load to maintain seal surface pressure.

The velocity of sound in a body (e.g., a bolt).  A term used in the ultrasonic measurement of bolt stress or strain.

The average value of a number of data points.  Computed by dividing the sum of all data by the number of data points.

The “catalog diameter” of a fastener.  Usually roughly equal to the diameter of the body, or the outer diameter of the threads.

An experimental constant used to evaluate or describe the ratio between the torque applied to a fastener and the Preload achieved as a result.

A measure of the ease with which a fluid can pass through a gasket material.

The nominal distance between two adjacent thread roots or crests.

The tension created in a threaded fastener when the nut is first tightened.  Often used interchangeably, but incorrectly, with working load, bolt force or bolt tension.

A measure of the precision with which a given tool or procedure creates preload in a bolt when the bolt is tightened.  A common torque wrench, for example, is said to produce preload with an accuracy of +30%.  The mean preload, however, may not be that which the designer intended, or may not be what he should have intended.  Accuracy as used here, in other words, is synonymous with Scatter.

Torque required to run a nut down against the joint when some obstruction, such as a plastic insert in the threads, or a noncircular thread, or other, has been introduced to help the fastener resist vibration loosening.  Prevailing torque, unlike
“normal” torque on a nut or bolt, is not proportional to the Preload in the fastener.

The maximum, safe, static, tensile load which can be placed on a fastener without yielding it.  Sometimes given as a force (in lb or N) sometimes as a stress (in psi or MPa).

Numerical value resulting from the multiplication of the internal pressure by the temperature of the fluid being sealed.  Provides only a rough guide for limiting gasket usage.

Pressure vessel research committee (USA)

A flange which makes contact with its mating joint member only in the region where the gasket is located.  The faces of the flange do not make contact with each other at the bolt circle.

Increase of thickness over the compressed thickness, once the compressive load has been removed

Material (such as fabric, cord and/or metal) within the gasket matrix, which imparts increased tensile strength or other desirable properties.

The loss of tension, and therefore Clamping force, in a bolt and joint as a result of Embedment, vibration loosening, gasket creep, differential thermal expansion, etc.

The tension which remains in an unloaded bolted joint after Relaxation.

Stress remaining in a gasket after service for a given time.

A flange system in which both flanges are grooved to accept a ring-joint gasket

A gasket machined from metal (usually oval or octagonal in cross-section) and used in conjunction with ring-joint flanges.

A thread formed by plastically deforming the surface of the blank rather than by cutting operations.  Increases fatigue life and thread strength, but is not possible (or perhaps economical) on larger sizes.

Room temperature operational tightness test, as defined by the PVRC.

Data points or calculations are said to be scattered when they are not all the same.  A “lot of scatter in preload” means wide variation in the preloads found in individual bolts.

Ability of a gasket material to prevent flow of fluid through the body and/or over the surfaces.

The portion of a bolt which lies under the head.

A joint which is subjected primarily to loads acting more or less perpendicular to the axes of the bolts.

A box wrench with an anvil on the end of the handle.  Torque is produced by striking the anvil with a sledge hammer.  Called a flogging wrench in England.

A washer whose upper surface is semispherical.  Used with a nut whose contact face is also semispherical.  Reduces bending stress in a bolt or stud, by allowing some self-alignment and/or some compensation for nonparallel joint surfaces or Angularity.

A gasket design which is formed by winding spring-like material, usually “V” shaped, plus a suitable filler material, into a spiral.

Equivalent to the “stiffness” of a bolt and defined as the initial preload divided by the elongation of the bolt after application of load.

A statistical term used to quantify the Scatter in a set of data points.  If the standard deviation is small, most of the data points are “nearly equal.”  A large deviation means less agreement.

Ability of a body to resist deformation due to the action of external forces.  Reciprocal of elasticity.

Change in dimensions or shape of a body due to applied force or stress.

The effective cross-sectional area of the threaded section of a fastener.  Used to compute average stress levels in that section.  Based on the mean of pitch and minor diameters.

A common form of Stress cracking in which an Electrolyte encourages the growth of a crack in a highly stressed bolt.  Only a tiny quantity of electrolyte need be present, at the tip or face of the crack.

A family of failure modes, each of which involves high stress and chemical action.  The family includes Hydrogen embrittlement, Stress corrosion cracking, stress embrittlement, and hydrogen-assisted stress corrosion.

A calibration constant used in ultrasonic measurement of bolt stress or strain.  It is the ratio between the change in ultrasonic transit time caused by the change in length of the fastener, under load, to the total change in transit time (which is also affected by a change in the stress level).

Loss of stress at a constant gasket thickness as a function of time, after application of a specified compressive load at a specified rate, at constant temperature.

A headless threaded fastener threaded on both ends, with an unthreaded body in the middle section, or threaded from end to end.  Used with two nuts, or with one nut and a tapped hole.

Fine irregularities of the flange surface finish.

A calibration constant used in ultrasonic measurement of bolt stress or strain.  Accounts for the effects of thermal expansion and the temperature-induced change in the velocity of sound.

Breaking tensile force divided by the original cross-sectional a

Tension (tensile stress) created in the bolt by assembly preloads and/or such things as thermal expansion, service loads, etc.

A joint which is primarily subjected to loads acting more or less parallel to the axes of the bolts.

A hydraulic tool used to tighten a fastener by stretching it rather than by applying a substantial torque to the nut.  After the tensioner has stretched the bolt or stud, the nut is run down against the joint with a modest torque, and the tensioner is disengaged from the fastener.  The nut holds the stretch produced by the tensioner.

The cross-sectional shape of the threads, defining thread angle, root, and crest profiles, etc.

Length of that portion of the fastener which contains threads cut or rolled to full depth.

That portion of the threads which are not cut or rolled full depth, but which provide the transition between full-depth threads and the body or head.  Officially called thread washout or vanish, although the term run-out is more popular.  (Run-out is officially reserved for rotational eccentricity, as defined by total indicator reading or the like.)

Studs, bolts, and screws of all sorts, with associated nuts.

Maximum acceptable specific leakage rate for particular applications.

Mathematical relationship between the measured specific leakage rate and the internal fluid pressure causing it.

A flange system in which one flange is provided with an annular tongue and the other with a complimentary groove to accept it.

The twisting moment, product of force and wrench length, applied to a nut or bolt.

A torque tool control system which monitors the amount of torque being developed by the tool during use, but does not control the tool or the torque produced.

A gearbox used to multiply the torque produced by a small hand wrench (usually a Torque wrench).  The output of the multiplier drives the nut or bolt with a torque that is higher, and a speed that is lower, than input torque and speed.  There is no torque gage or readout on the multiplier.

A manual wrench which incorporates a gage or measuring apparatus of some sort to measure and display the amount of torque being delivered to the nut or bolt.  All wrenches produce torque.  Only a torque wrench tells how much torque.

A device which converts one form of energy into another.  An ultrasonic transducer, for example, converts electrical energy into acoustic energy (at ultrasonic frequencies) and vice versa.

Sometimes used to describe the general rotation of the nut (or bolt head) as the fastener is tightened.  More often used to define a particular tightening procedure in which a fastener is first tightened with a preselected torque, and is then tightened further by giving the nut an additional, measured, turn such as “three flats” (180°).

The maximum tensile strength a bolt or material can support prior to rupture.  Always found the plastic region of the stress-strain or force-elongation curve, and so is not a design strength. Also called Tensile strength and ultimate tensile strength.

An electronic instrument which measures the change in length of a fastener ultrasonically as, or before and after, the fastener is tightened.

A principal dimension of nuts or of bolt heads.

The slight increase in hardness and strength produced when a body is loaded past its yield point.  Also called strain hardening.

That stress level which will create a permanent deformation of 0.2% or 0.5% or some other small, preselected, amount in a body.  Approximately equal to the elastic and proportional limits of the material, a little higher than the proof strength of a bolt.